Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Cap & Crown for Ballantyne Homeowners
A missing or rusted-out cap is the most common reason water gets into a Ballantyne chimney, and by the time you notice a stain on the ceiling, the damage has usually been working quietly for a season or two. Our technicians have up to 13 years of experience fitting caps and rebuilding crowns on the brick chimneys throughout this part of south Charlotte, and we bring the same professional-grade Gelco and Famco materials used by certified chimney specialists nationwide. We answer 24/7, and cap and crown work can often be scheduled for the same day. Call (888) 495-1677 to set up a free estimate.
What Our Chimney Cap & Crown Service Includes
A chimney cap sits on top of the flue and keeps rain, birds, squirrels and sparks where they belong. The crown is the sloped concrete or mortar surface capping the brickwork itself. They fail differently and get repaired differently, so we treat them as two jobs that protect the same structure. Here is what each one involves.
Cap Installation
A new cap is the single cheapest piece of protection you can add to a chimney, and it goes on any flue that has been running open. We measure the flue opening, match the cap to the flue size and choose a mesh rating that suits your fireplace or appliance. Installation includes seating the cap so it sheds water away from the crown instead of pooling on it. If your flue has never had one, this is the first thing we’ll recommend after a sweep.

Cap Replacement
Old caps rust through, lose their screens to storm debris, or blow loose in high wind and end up sitting crooked on the flue. A crooked or missing cap lets water straight into the flue, which is hard on the liner and the firebox below. We pull the old unit, inspect the flue tile and crown for damage the cap may have been hiding, then fit a replacement sized to the same opening. If the previous cap came off in a storm, we’ll check the crown for cracks while we’re up there at no extra charge.

Crown Repair
Hairline cracks in the crown are normal on an older masonry chimney, but once water gets behind the crown it freezes, expands and lifts the concrete apart. We cut out the failed sections, rebuild the slope so water runs off the edge rather than sitting on top, and seal the joint where crown meets flue tile. This is work that has to be done with the right mortar mix; a crown patched with ordinary concrete tends to crack again within a couple of winters.

Crown Coating
Crown coating is a flexible, waterproof membrane applied over a sound crown that has minor surface checking but no structural failure. It bridges small cracks and gives the concrete a wear layer that handles freeze-thaw cycles better than bare mortar. We only recommend coating when the crown underneath is still intact; if it’s crumbling or pulling away from the flue, repair comes first and coating goes on afterward.
Multi-Flue Cap
A multi-flue cap is a single top-mounted unit that covers two or more flues at once, common on the large masonry chimneys you see on older homes around Ballantyne. It has to be custom-fitted to the exact flue spacing, because a generic cap that doesn’t align lets water run down into the wrong flue. We measure the whole chimney top, note which flues are active and any appliance vents, and order a unit built to those dimensions.
Custom Cap
Chimneys with unusual dimensions, oversized flues or decorative masonry tops need a cap made to fit them rather than a stock size forced into place. We use Copperfield for custom work because the material holds up to weather and can be built to spec for the odd sizes we run into on older properties. The result is a cap that looks like it belongs on the house and stays put through wind that would lift a cheap galvanized unit.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Cap & Crown
We fit and service caps and crown systems from the brands professional chimney contractors rely on. Gelco and Famco supply the crown and cap components we install most, and both hold up well in the freeze-thaw swing that a Ballantyne winter brings. When we’re matching a replacement to existing masonry, working with manufacturer-matched parts is what makes the fit reliable instead of approximate. We know where each of these holds up and where it tends to wear first, so a repair is targeted rather than a whole replacement.
For flue protection underneath the cap, we work with DuraFlex flexible stainless liner systems and HeatShield ceramic liner resurfacing when the flue itself needs attention. If your cap or crown job turns into liner work, we handle it in-house rather than handing you off to another contractor. Whether you have Famco, Copperfield, Gelco or any other make on your chimney, we can help. It’s the same standard we hold across every Chimney Sweep Ballantyne service we provide.
Signs You Need Chimney Cap & Crown Right Now
- Water stains or rust in the firebox. Brown streaks down the firebox walls or a rusted damper usually mean the cap is missing or the crown is cracked. Both let water travel down the flue and pool at the bottom, where it works on metal and mortar.
- Visible cracks or crumbled mortar on the crown. If you can see cracks from the ground, or chunks of the crown have fallen onto the roof, the crown has already failed. Small cracks widen with each freeze and let water into the brickwork below.
- Birds, squirrels or debris in the flue. An open flue is an invitation, and nests block the draft and create a fire hazard. A screened cap solves it, and we’ll clear whatever has already moved in.
- A cap that’s crooked, loose or missing after a storm. A cap sitting at an angle no longer sheds water away from the crown; it channels it toward the mortar joint instead. Loose caps also rattle in wind and can tear the flue tile if they drop.
- White staining on the exterior brick. Powdery white deposits on the outside of the chimney point to moisture moving through the masonry. It’s often the crown failing first and the brick absorbing the result, so it’s worth checking before the brick itself starts to spall.
Our Chimney Cap & Crown Process – Step by Step
- 1
Look while we clean. A sweep is only as good as the inspection that comes with it. We run a camera down the flue and photograph the crown and cap from the roof so you can see exactly what condition everything is in, not just take our word for it.
- 2
Show you what we found. We walk through the photos with you and separate the urgent from the routine. If the crown is sound and only the cap needs replacing, we’ll say so, and if a repair can safely wait a season, we’ll tell you that too.
- 3
Match the material to the job. Crown repairs get the right mortar mix and a rebuilt slope; caps get sized to the flue opening and matched to the manufacturer’s spec. For odd sizes or multi-flue setups, we measure everything before ordering anything.
- 4
Do the work in one visit where possible. Cap installation and most crown repairs happen in a single appointment. Larger crown rebuilds may need a return visit once the initial repair has cured, and we’ll tell you which category yours falls into before we start.
- 5
Confirm it sheds water. We check the finished cap and crown from the roof, confirm the slope runs water away from the flue, and send you the before-and-after photos so you have a record of the work.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Ballantyne?
Chimney cap installation in Ballantyne typically runs $175 – $425 depending on flue size and cap style, and a straightforward crown repair usually lands between $300 and $700. Multi-flue and custom caps cost more because they’re built to measure, generally $450 – $1,200, while crown coating on a sound crown is the least expensive option at $250 – $500. Treat these as estimates for the typical job; the written estimate sets the final price, and it’s free.
What pushes a job up: the number of flues, how much of the crown has to be cut out and rebuilt, whether the chimney has a decorative masonry top that complicates fitting a cap, and whether we find liner damage underneath once the old cap comes off. What keeps it down: catching a failing crown before it’s cracked all the way through, and choosing a cap sized correctly the first time rather than a hardware-store unit that has to be replaced in a few years.
We agree a flat price before booking, and nothing gets recommended without camera evidence you can see for yourself. If a crown repair can wait until spring without risk, we’ll tell you. That’s the same approach we take with our chimney cap & crown work across the area.
Chimney Cap & Crown Near Ballantyne – Our Service Area
We work chimney cap and crown jobs throughout Ballantyne and the surrounding communities, including Providence, Marvin, Weddington, Pineville, Matthews and Waxhaw. Response times depend on where you are and what’s already on the schedule, but most jobs in and around Ballantyne get booked quickly. If you’re over toward the Quail Hollow side of town, see our chimney cap & crown page for that area, or check the chimney cap & crown details for Beverly Woods.
Serving Ballantyne, NC – Our Local Coverage Area
We serve Ballantyne and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Cap & Crown in Ballantyne
A chimney cap is the unit that sits on top of the flue and keeps rain, animals and sparks out; the crown is the sloped concrete or mortar surface that caps the brickwork itself. They protect different parts of the chimney: the cap guards the flue opening, and the crown sheds water off the masonry so it doesn’t soak into the brick. Both fail over time, and both are repairable.
Most cap installations and small crown repairs are done in a single visit, usually a couple of hours depending on roof access and the number of flues. Larger crown rebuilds may need a second visit once the mortar has cured. We’ll give you a realistic window when we quote the job rather than a guess on the day.
A standard cap installation typically runs $175 – $425, a crown repair about $300 – $700, and a multi-flue or custom cap $450 – $1,200. Crown coating on a sound crown is generally $250 – $500. The written estimate sets the final price, and the estimate itself is free. Call (888) 495-1677 for an exact quote.
Yes. We work with Famco and Copperfield as well as Gelco, and we can match replacement parts to an existing setup where the original brand is still available. If your cap is a different make entirely, we can still assess it and recommend a replacement that fits the flue properly. Brand rarely matters as much as correct sizing and a sound crown underneath. Call (888) 495-1677 to book a look.
Same-day service is often possible for cap and crown jobs, depending on the schedule and the scope of work. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. We’re closed Saturday. Call (888) 495-1677 and we’ll find you a slot.
We stand behind the materials we install and the workmanship on every job. The specific terms depend on the product and the scope, so we spell them out in writing in your estimate rather than quoting a blanket promise. Ask us directly when we’re on site and we’ll go through exactly what’s covered. Call (888) 495-1677 with any questions before booking.
Clear access to the fireplace and hearth, and make sure we can get to the roof or the chimney from outside. If you have pets, keep them away from the work area during the visit. Beyond that, there’s nothing to prepare; we bring everything we need for the job. Call (888) 495-1677 to schedule.
Schedule Your Chimney Cap & Crown Service in Ballantyne Today
Don’t wait for a water stain to tell you the crown has failed. Whether it’s a new cap, a crumbling crown or a custom fit on an older chimney, we’ll give you a straight answer and a free, no-obligation estimate. Call (888) 495-1677. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to 13 years of experience and handle the full chimney system, from chimney repair to chimney inspection, all in-house.
Written by the team at Chimney Sweep Ballantyne.